※ Not available any more.

☞ move to New DroneKeeper micro

※※※  Please read ※※※ 

1. This DroneKeeper mini is KIT version without Li-Po battery. After the customer purchases the battery, should assemble the battery and shrink tube by yourself directly.

2. We're not responsible for any defects that occur during assembly.
3. This DroneKeeper min KIT can be shipped via Air registered small packet. In order to select the air registered small packet shipping, please add FREE-PAY item in shopping cart.

※※※ Caution ※※※

- This product contains mechanical parts which are weak to impact such as Buzzer, Battery and Switch.

  Therefore, it is very important that the installation is done so that the direct impact of these parts do not be applied when drone falls.

- Please refer to the installation example at the top to optimize it for your own drone.

- Never remove the silicone tube from the auxiliary buzzer connector(BUZ-CON) when not using the auxiliary buzzer.

  Do not connect any devices intentionally or accidentally to the auxiliary buzzer connector(BUZ-CON).

  The buzzer may not sound when connected.

Change History of Firmware

**The latest firmware is 2.5 (Only missing alarm timing has been changed)
(before Jun 30, 2016)
(after July 1, 2016)


  • The missing alarm will ring instead of the low voltage alarm when the external battery is disconnected while the external battery is being connected to the DroneKeeper mini.

low voltage alarm

missing alarm

 Wireless Mode only

  • Trigger point of motion sensor timer: User can select the trigger point of motion sensor timer(30sec, 1min, 5min, 8min, 10min). 
    The missing alarm will ring after the trigger point of motion sensor timer if there is no any movement. 


  • Trigger point of power on timer: User can select the trigger point of power on timer(30min, 60min, 90min). 
    The missing alarm will always ring after power on regardless of motion sensor status to prepare the worst case. (ex: strong wind) 


  • Sensitivity of motion sensor


fixed 30sec














(30sec, 1min, 5min, 8min, 10min)





(30min, 60min, 90min)






 Wired Mode only 

  • Trigger point of R/C receiver signal was changed for the missing alarm







  • DroneKeeper Mini is the 2nd generation stand-alone audible sound locator to find lost drones with internal battery
  • Can work without any connection with built-in Motion sensor
  • Can use all kinds of drone
  • Supports 2 in 1 function (Locator + Low voltage alarm) 
  • High quality, performance and lightweight(6g)
  • Very easy to use, just mount on drone
  • Can work regardless of main battery status
  • Possible to recognize the beep sound in a noisy downtown area within a 50~60meter(164~197feet) radius



  • Missing alarm will ring if there is no any movement of drone at Wireless mode
  • Missing alarm will ring if a receiver loses signal or power at Wired mode
  • Can connect the auxiliary buzzer 
  • Supports 2 kinds of user mode (Wireless mode, Wired mode)
  • Built-in motion sensor for Wireless mode
  • Can change the trigger point of motion sensor timer(30sec, 1min, 5min, 8min, 10min)
  • Can change the trigger point of power on timer(30min, 60min, 90min) 
  • Supports Low battery voltage alarm for external battery(main battery of drone) and can be changed from 3.2V to 3.6V by user
  • Supports Low battery voltage alarm for internal battery
  • Wide input voltage range from 5V to 17V (LiPo 2S to 4S)
  • Power switch off detection alarm at Wired mode only
  • Automatic internal battery charging when external power is connected
  • Can also charge the internal battery via the PC USB port using a provied micro USB module
  • Pb-free, Internal battery with PCM(Protect Circuit Module) 



 Input VoltageDC 5V ~ 17V (LiPo 2S ~ 4S) via RCV-CON (※2S~3S recommend)
 Power consumptionStandby: max 26mW, Operation: max 189mW
 Battery life time

Operating time: about 2.5hours @since the missing alarm rings 

Stand-by time: about 6.5hours @without the missing alarm 

 Charging time of the internal batteryabout 1hour after full discharged 
 R/C receiver reference signal pulse widthPWM center 1,500us [1.5ms], compatible with most of receiver
 Sound pressure levelmin 90dB @10cm 
 Operating temperature-10˚C ~ 50˚C 
Dimensions35mm x 14mm x 11mm 


Included in the Box

※ Battery is not included.

DroneKeeper mini PCBA x1microUSB charging module x1

Shrink Tube(Yellow color) x1Battery Bed & Double side adhesive tape x1

Battery connection wire x1Quick start guide x1


☞ Manual download: Click here!

☞ User timer setting Manual for firmware2.0 and later versions download: Click here!

Example of assembly

☞ Required Tools: Soldering Iron, Heat Gun

☞ Recommended Li-Po battery: 60~70mAh / 3.7V with PCM (Size: Length 20mm, Width 12mm, Thickness 4mm)

<1> Power switch should be turned OFF during soldering.

<2> Soldering the battery wires to the battery pad of the DroneKeeper mini PCBA

        Attaching the provided double side adhesive tape to both RCV-CON connector and battery.

        ※CAUTION: Never reverse the polarity of battery!  If so, the DroneKeeper mini will be damaged.

<3> Attaching the battery to the Battery Bed

<4>  Turning over the battery ass'y


<5>  Attaching the battery ass'y to the RCV-CON connector

<6>  Covering the provide shrink tube using heat gun (※Be careful of damage from HOT temperature!)



   [1] Please do not tie the Dronekeeper mini too tightly.

         It will make things worse. 

   [2] If the ESC doesn't have a high capacity electrolytic capacitor on battery input, not recommend to connect the 4cell LiPo battery because of high ripple noise by motor.



Released: 2017.9.1 

Write a review

Note: HTML is not translated!
    Bad           Good

DroneKeeper Mini(KIT)

  • Product Code: SSB-70D-KIT
  • Availability: Out Of Stock
  • $0.00

Related Products

DroneKeeper Mini

DroneKeeper Mini

※ Not available any more.☞ move to New DroneKeeper mini2☞ move to DroneKeeper micro※※..


Battery connection wire

Battery connection wire

Battery connection wire for the low voltage alarm of external batteryTo use the low voltage alarm of..


microUSB charging module

microUSB charging module

microUSB charging module for DronKeeper Mini...


Touch pen wire

Touch pen wire

Touch pen wire for changing the user timer setting values (can be also used..


Auxiliary Buzzer

Auxiliary Buzzer

Auxiliary buzzer for SSB-70D version only of DroneKeeper Mini. Adhesive tape is attac..




Buzzer for DroneKeeper mini and DroneKeeper mini2 Released: 2017.2.27..




Switch for DroneKeeper mini and DroneKeeper mini2 Released: 2017.2.27..


Shrink Tube

Shrink Tube

Shrink tube for DroneKeeper mini※ Yellow color is only available.  Released: 2017.2.2..


Free Pay

Free Pay

Free Pay..